I INCINERATOR
1. Type Air Oil Fired Incinerator
2. Type of Waste Medical Waste
3. Burning Capacity (As per 250 beds hospital Bio Wast Desposal)
4. Auxiliary Fuel Diesel
5. Type of Burner Operation Monoblock fully automatic burners
6. Temperature
Primary Chamber Secondary Chamber 8000±500C
1050±500C
II PRIMARY CHAMBER
1. Type Static Solid Hearth
2. Material of Construction Mild Steel, 5mm thick
3. Refractorythickness 115mm thick
4. Material Refractory bricks confirming to IS-8
5. Temperatureresistance 14000C
6. Insulation thickness 115mm thick
7. Material Insulation bricks confirming to IS-2042
8. Waste Charging Automatic
9. Ash Removal Manual
III SECONDARY CHAMBER
1. Type Static Solid Hearth
2. Material of Construction Mild Steel, 5mm thick
3. Refractorythickness 115mm thick
4. Material Refractory bricks confirming to IS-8
5. Temperatureresistance 14000C
6. Insulation thickness 115mm
7. Material Insulation bricks confirming to IS-2042
IV EMERGENCY STACK
1. MOC Mild Steel, 3mm thick
2. Refractory 75mm thick castable
3. Insulation 25mm thick castable
V QUENCHER
1 MOC of outer body Mild Steel refractory lined from inside
2 Water Circulation system Provided with centrifugal pump
3 Purpose To reduce flue gas temperature before venturi scrubber
4 Pump motor Suitable capacity provided as per our design
VI AIR POLLUTION CONTROL DEVICE – VENTURI SCRUBBER
1 Type High Pressure Jet Type
2 MOC Stainless steel – 316L
3 Temperature at the outlet 78-800C
4 Scrubbing Media Water with 5% caustic
VII RE- CIRCULATION PUMP FOR VENTURI SCRUBBER
1 Type Centrifugal
2 Application PP/SS
3 Piping PPR
VIII DROPLET SEPARATOR & RE-CIRCULATION TANK (INTEGREL)
1 Type Cyclonic
2 Application To separate water droplets from flue gases
3 MOC Mild Steel Rubber lined 3mm thick
IX I.D. FAN
1 Type High Pressure Centrifugal type
2 MOC Stainless Steel Impeller and Mild Steel Rubber lined casting
3 Drive Belt Driven
X COMBUSTION FAN
1 Type Centrifugal
2 Modulation Manual damper control
3 MOC Mild Steel
4 Drive Direct drive
XI BURNERS
1 No. of burners 2 Nos. (1 No. in Primary Chamber and 1 No. in Secondary Chamber)
2 Type Monoblock fully automatic
3 Fuel Diesel
XII FUEL OIL STORAGE TANK
1 MOC & Capacity Mild Steel, suitable capacity
2 Other Standard Accessories Diesel Oil level indicator, piping with valves
& N.R. Valve
3 Visual checking of Fuel To be Provided
XIII CONTROL PANEL
1 Type PLC based with printer & recording device having both Manual and Auto Operation
2 MOC CRCA Sheet
3 Type of temperature controller Digital
4 Finish & Painting type Powder coated
5 Audio-visual alarm system To be Provided
XIV CHIMNEY OF 30 MTRS HEIGHT
1 MOC Mild Steel
2 Type Self supporting
3 Height 30 mtrs from ground level
4 Other Standard Accessories Aviation lamp, lightening arrestor, stack, drain, inspection platform, sampling port
5 Paint The chimney is painted externally with two coats of heat resistant aluminium paint
6 Ladder To be Provided till the top
7 Inside Protection 3mm thick rubber lining from inside
XV CERTIFICATION
1 Approval PCB approved machine
2 Mandatory approvals for operation All mandatory approvals (if any) required for the installation and operation of incinerator shall be done by the successful bidder.
XVI TRAINING
1 Training The successful bidder shall train the hospital staff to the satisfaction of the authorities.
XVII TURNKEY
1. Equipment to be installed a t s i t e a s d i re c t e d b y p r o j e c t d i r e c t o r . The civil works required to install the new machine has to be included in the offer.